102 WWW.HOGSLAT.COM A) #2020290203 29” Flat bar, 2”x 17” foot B) #2000830200 29” Flat bar, 8”x16” plate C) #2020520202 29” Flat bar, w/ 2”x17” foot, gate clip w/ inside pipe one side D) #2040050201 29” Flat bar post, 2”x19” foot, with divider clips 29” Tall Galvanized Bolt-On Legs D. C. A. B. #5000641200.......Angle Bottom, Bolt-On Leg Pkg • Mounts on any brand of angle bottom penning • Hot Dipped Galvanized • Use where bottom angle has rusted preventing the use of a standard angle leg • 2” x 17” Foot • Height -12” • Wt -6.9 lbs Cast T-Bolt #5000441200........ Galv. w/ 17” foot & hardware pkg #5000441502............SS w/ 17” foot & hardware pkg #5000401200........ Galv. w/ 10” foot & hardware pkg • Hot Dipped Galvanized or Stainless Steel • Adapts to Any Horizontal Fencing • Complete with bolts, nut, washers and back-up plate #5000870500. ...... For middle of panel (EIP style) • 1/4” Stainless Steel construction • Use for mid gate leg for EIP style gating #5000841500................ for angle bottom penning #5000850500.......................... bolt-on top bracket • Heavy Stainless Steel Leg for Angle Penning • Mounts to Any Brand Angle Bottom Gate #8250730208..... 8”x 13” Plate w/ 6” x 1-3/4” solid shaft • Fits inside of 2” post • Weld in place • Galvanized #5000880500................. For end of panel (EIP style) • 1/4” Stainless Steel Construction • Mounts on the end of EIP style penning or at a feeder opening #3090451000...................1/2” x 4-1/2” - Cast Iron #3090451002...................1/2” x 5-1/2” - Cast Iron #60583...................................... 1/2” flat SS washer #60831.....................................SS Bolt 1/2” x 4-1/2” #60828....................................SS Bolt 1/2” x 5-1/2” #3090700000............................. Cast Iron tee only • Comes with Stainless Steel bolt T-Bolt and Nut Package #3090401500.................. 3/8” x 1-1/2” - Stainless #3090421500.................. 3/8” x 5-1/2” - Stainless #3090601500.......................... 1/2” x 5” - Stainless #3090441500.................. 1/2” x 5-1/2” - Stainless #3090521500.................. 1/2” x 6-1/2” - Stainless • Includes hex nut & washer #3090900100 �������������������������������������������������������������������������������������������������������������������������Cast T-nut wrench #3090910100 ��������������������������������������������������������������������������������������������������������������������������������� T-bolt wrench T-Bolt Wrench • Holds T-bolts in place while you tighten the nut. • Allows you to replace T-bolts from the top of the slats. • Makes installing T-Bolts simple! STOP DROPPING T-BOLTS INTO THE PIT!!! The tabbed design allows installation from above the floor without extra tools. Slide the encased nut assembly through the flooring slots and the winged tabs hold it in place until the bolt is tightened. After securing equipment the wings can be cut off. Package of 4. Hog Slat Plastic Floor Anchor #HS652-50..................M8-1.25 x 50mm long bolt #HS652-90..................M8-1.25 x 90mm long bolt WARNING: This product can expose you to chemicals, including nickel, which is known to the State of California to cause cancer and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov
RkJQdWJsaXNoZXIy MTA3MzU=